WFC Kingdom Galvatron misassembled shoulders

[Skyfire]

Since wave 3 of WFC Kingdom is showing up more around the country, and since we know the first batch has the shoulders misassembled in some cases, it might be of interest to see what percentage we've encountered for those who want to hold off buying.

Over time the shoulder problem will be removed at the factory since Hasbro surely must be aware of it. I've also heard a rumour that Galvatron will be released again in the future.

If you have more than one copy, I've hopefully allowed the poll to take both answers but I don't think it can take more than one of each answer... hmm. Sorry, it's my first poll.

[GoktimusPrime]

Oops, I misread the poll question and thought it said "incorrectly" and voted "YES."
I meant no. Mea culpa. :p

[Skyfire]

Oops, I misread the poll question and thought it said "incorrectly" and voted "YES."
I meant no. Mea culpa. :p

That's ok. I'm probably going to wait for a good one and your "yes" will be my "yes". Unless I find a $44 Big W Toy Mania one... hmm... decisions, decisions.

[ComradeRenko]

20 minutes with a screw driver last night resulted in fixed shoulders and minimal stress marks. It's not for everyone, but it was actually easier than I'd feared it would be.

[VERT]

To make it even easier. Pop his shoulders in a cup of boiled water first. Pin will come out easy. No stress marks

[Skyfire]

I bought one at Myer Perth CBD. There were 2 - one of each shoulder variant. So I will use Gok's mistaken yes as my yes but I won't record the bad one since I did not buy it. It's good we are getting some good shoulder copies at least. I read a rumour that Singapore and Malaysia are not getting any good ones this year and the Singapore TFW2005 sightings are showing bad copies so far.

[Paulbot]

Bought from a Toyworld the date before lockdown, it was the only one in the shop but compared to photos online the shoulders are fine. Is fine out of the box.

[Seraphim Prime]

The easy way to check will be to see if the shoulder is fully rounded on the top, or if it has the square marks on the top.

The difference is literally measured in millimetres - both it is noticeable in both robot and cannon modes

[Dimi194]

Mine was incorrectly assembled, but no issues with just rotating the joint around.

[kovert]

Another way to tell could be the production code. The ones with a later production code should be more likely to have the correctly assembled shoulders. My copy of Kingdom Galvatron with correctly assembled shoulders has '11371' stamped on the back of the box near the 'SC' symbol. Presumably '11371' means 17 May 2021.

[Skyfire]

Another way to tell could be the production code. The ones with a later production code should be more likely to have the correctly assembled shoulders. My copy of Kingdom Galvatron with correctly assembled shoulders has '11371' stamped on the back of the box near the 'SC' symbol. Presumably '11371' means 17 May 2021.

Mine is the same as yours.

[Thurmus]

Excuse my stupidity, what is the SC symbol?

[Thurmus]

All good. I reread the stamped part and decided to look at the box on an angle. My stamp was under the tape so it was hard to see.

[kovert]

Mine is the same as yours.

Considering they needed to be shipped all the way to Australia, they are fairly recent copies. Just a little over two months old.


All good. I reread the stamped part and decided to look at the box on an angle. My stamp was under the tape so it was hard to see.

The 'SC' (or 'CS') is probably a toy safety certificate symbol for Argentina. What's the date code on your copy?

[Seraphim Prime]

Another way to tell could be the production code. The ones with a later production code should be more likely to have the correctly assembled shoulders. My copy of Kingdom Galvatron with correctly assembled shoulders has '11371' stamped on the back of the box near the 'SC' symbol. Presumably '11371' means 17 May 2021.

Mine was 10831 (which I understand is 24 March)

1 - Year
083 - Day within the year
1 - Location of production

[Skyfire]

I bought another good shoulder copy for a present, among 7 bad ones at Toymate. The batch number is 11231. Added one YES to the poll.