Results 1 to 10 of 36

Thread: Damaged During Transformation Help!

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    Join Date
    29th Dec 2007
    Location
    NSW
    Posts
    14,762

    Default

    Yeah it doesn't seem wise to disassemble it given the pin and the fragile joint. Going with the glue seems like the best shot. Just try to practice with the glue a bit before trying. Also see about covering up with thick masking tape the joint area so that if there is an accident, it doesn't spill on the plastic itself.

    In the unfortunate event that it does break off completely, I would recommend pulling the pin out then and try to loosen up the joint. That way once you glue the piece back, it won't have anywhere as much friction and be less stressful on the plastic.

    How did it happen anyways? First time I hear of this. I know this used to be a problem with G1 Hook.

  2. #2
    Iriorne is offline Rank 6 - Dedicated Member
    Join Date
    31st Oct 2012
    Location
    Melbourne
    Posts
    411

    Default

    Good news: the Zap-a-Gap glue seems to have done its job and after a few applications the crack has been completely filled. No photo, since it looks almost exactly the same, there's just a slight shine from the glue when it catches the light. It's not a very high stress joint (usually!) so with a little care I don't expect any more problems.

    Quote Originally Posted by Kup
    How did it happen anyways? First time I hear of this.
    Yeah, it was totally my fault. I was converting him back from combined mode and applied too much torsional stress to the hinge. There's a grey latch on Mobile crane to help keep the two halves together in combined mode. It's pretty flexible anyway but you have to bend it quite a bit to detach. To lessen the stress on it while detaching I twisted the crane halves apart a little as well. It seemed like a good idea at the time but I wasn't thinking about where all that stress would end up - in the hinge attachment point. The plastic is quite hard so there was very little movement until the plastic suddenly gave in and twisted.

    Anyway, lesson learned: Flexible plastic is for bending.

    For anyone who needs to apply glue to small fiddly bits, there's a good modeller's trick that's equally applicable to toy repairs.

    Rather than squeeze glue direct from the bottle onto the part, squeeze a drop or two onto a non-porous surface like a ceramic tile or an old plate. I use glass microscope slides but bottle tops or even greaseproof or waxed paper might work. You can then dip a sewing pin or toothpick into the puddle of glue and pick up a small bead of glue, which you can then apply to the part, giving you much finer control over the amount and placement of the glue. If bits are completely snapped off you can even dip the end directly into the glue puddle for an even coat.

  3. #3
    Join Date
    7th Mar 2012
    Location
    The Moon
    Posts
    6,605

    Default

    Quote Originally Posted by Iriorne View Post
    Good news: the Zap-a-Gap glue seems to have done its job and after a few applications the crack has been completely filled. No photo, since it looks almost exactly the same, there's just a slight shine from the glue when it catches the light. It's not a very high stress joint (usually!) so with a little care I don't expect any more problems.



    Yeah, it was totally my fault. I was converting him back from combined mode and applied too much torsional stress to the hinge. There's a grey latch on Mobile crane to help keep the two halves together in combined mode. It's pretty flexible anyway but you have to bend it quite a bit to detach. To lessen the stress on it while detaching I twisted the crane halves apart a little as well. It seemed like a good idea at the time but I wasn't thinking about where all that stress would end up - in the hinge attachment point. The plastic is quite hard so there was very little movement until the plastic suddenly gave in and twisted.

    Anyway, lesson learned: Flexible plastic is for bending.

    For anyone who needs to apply glue to small fiddly bits, there's a good modeller's trick that's equally applicable to toy repairs.

    Rather than squeeze glue direct from the bottle onto the part, squeeze a drop or two onto a non-porous surface like a ceramic tile or an old plate. I use glass microscope slides but bottle tops or even greaseproof or waxed paper might work. You can then dip a sewing pin or toothpick into the puddle of glue and pick up a small bead of glue, which you can then apply to the part, giving you much finer control over the amount and placement of the glue. If bits are completely snapped off you can even dip the end directly into the glue puddle for an even coat.
    I don't use that latch for that very reason. Not using it doesn't affect the stability of the combined mode at all. Just a tip for the future.
    Dovie'andi se tovya sagain

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •