I probably should have put a disclaimer there. I use lacquers so if you mix and match paints you're going to have problems. You can use it over Tamiya spray cans, Mr Color, Gaianotes, Finishers etc.Originally Posted by Iriorne
Rank 9 - Board Staff
I probably should have put a disclaimer there. I use lacquers so if you mix and match paints you're going to have problems. You can use it over Tamiya spray cans, Mr Color, Gaianotes, Finishers etc.
Rank 8 - Deluxe Member
Hey I was in eckersleys today and they had liquitex spray paints (professional spray paints) liquitex has a good rep, although I don't think I've seen many toy customisers use it. You buy the cans and the nozzles separately. The nozzles are different sizes, sorry didn't get any prices.
Rank 6 - Dedicated Member
Ah, thought that might be the case. I like Tamiya's basic lacquer primer but prefer to paint with acrylics because they're easy to clean and airbrush well over quite a wide range of pressures and paint/thinner ratios.
Cool, sounds pretty much the same as the fabled Future floor polish. Might give it a try next time - Bunnings sells it $10 a big bottle which beats $4 for 10 mL of Tamiya clear.
The website has them at $20 a can - pricey but the pigments should be artisan quality. I can't find any info on their use in scale modelling, but liquitex suggest it works well for graffiti art, so I suspect it might be pretty thick?
Rank 8 - Deluxe Member
There was a sample of how the paint looked sprayed on different materials. The plastic looked OK but it could be only one coat
Rank 3 - Basic Member
Went and had a look around
Masters had Plasti-kote Super Spray & Bunnings had White Knight Squirts has anyone tried using any of these?
Rank 8 - Deluxe Member
i used white knight clear acrylic satin...is really good....the gloss one too thick !
Rank 6 - Dedicated Member
I've not used either, but White Knight Squirts seems pretty popular for war gaming miniatures: http://www.wargamerau.com/forum/lofi...php/t9737.html
Plasti-kote could be ok too. The suggestion is to sit the can in some warm water first to get a finer spray, and you may need to overcoat with clear first if you're adding more paint or a wash.
http://www.dakkadakka.com/dakkaforum...st/265523.page
Rank 6 - Dedicated Member
For Tamiya sprays, how does the PS series work on ABS plastic? Not a tf project but currently, I'm building a 1/144 meteor strike and want to paint the base Lame Flake (PS49?). Is PS acrylic?
Rank 6 - Dedicated Member
Seems like it might be a bad idea.
Tamiya's own web site says the PS series are designed for use on transparent polycarbonate shells for R/C cars and should not be used on plastic models (styrene).
source
Someone else asked the same question on an R/C website and got the following answers:
The Tamiya "PS" series paints (polycarbonate series) etches into the plastic
and leaves a dull rough surface. This paint appears to be glossy only when
seen through the outside of the clear polycarbonate. The etching process
allows it to remain firmly attached to RC car body as it flexes whereas
Lacquers and enamels simply crack and peel off.
The PS paint is also used on metal models and then oversprayed with a clear
or matt coat.
PS may be used on plastic models which have been prepared with Tamiya Primer
or Preparacote.
Better to stick with the Tamiya "TS" series which is a hard lacquer (similar
to Topflite Lustercote) and fuel proof - leave to dry thoroughly between
coats and before exposure to fuel.sourcePolycarbonate is a thermoplastic or "plastic." I believe they are
refering to polystyrene models which are really high impact or rubber
modified polystyrene plastics. ABS is acrylonitrile-butadiene-styrene
plastics and it is basically high impact polystyrene with a third
monomer thrown in for thermal and chemical resistance, among other
properties. I'm not sure of the solvent used in the "polycarbonate"
paint, but would guess if it attacks polystyrene, it's not going to be
great for ABS parts.
Posting Permissions
Reply With Quote
