Results 1 to 10 of 29

Thread: De-Chroming bits and pieces how to guide

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    Join Date
    14th Nov 2008
    Location
    Perth
    Posts
    2,783

    Default De-Chroming bits and pieces how to guide

    I'm in the process of restoring an original G1 Galvatron, and part of that process involves the re-chroming of 3 of his 4 chrome parts (fortunately, his '4 pack' is faultless). Before I even think about applying any paint (I won't be using comparatively expensive plating techniques) I'll need to remove the chrome that is there, as seen below.



    To achieve this, I've gathered the following products:
    -Latex gloves (not pictured)
    -Easy-Off BAM @ $4.80
    -Paper Towel
    -Hard bristled Toothbrush
    -Small Container
    -Cotton wool bud (optional)



    Here are the steps taken to remove the chrome:
    Step 1: Put gloves on
    Step 2: Place the 3 parts into the small container
    Step 3: Pour enough Easy-Off BAM over the parts to cover them
    Step 4: Using the cotton wool bud and/or toothbrush, brush over the remaining chrome paint until all gone (there is no waiting period required, the chrome paint will come off easy peasy like taking Energon candy from a Minicon)
    Step 5: Wash the de-chromed parts in dishwashing detergent + warm water
    Step 6: Rinse them under cold water
    Step 7: Use paper towel to dry them off

    All done! Just look how happy Galvatron is with the results.


  2. #2
    Join Date
    27th Dec 2007
    Location
    Sydney
    Posts
    3,152

    Default

    Nice tips, I have to try that sometime. What I find interesting is that one type of remover that I use (Dawn Power Dissolver) is really basic while the Easy Off is really acidic, if I read the contents correctly, but both do the same job.

  3. #3
    Join Date
    14th Nov 2008
    Location
    Perth
    Posts
    2,783

    Default

    Quote Originally Posted by gamblor916 View Post
    Nice tips, I have to try that sometime. What I find interesting is that one type of remover that I use (Dawn Power Dissolver) is really basic while the Easy Off is really acidic, if I read the contents correctly, but both do the same job.
    Thanks Gamblor. Is Dawn Power Dissolver an oven cleaner? I've read that quite a few substances can do the job of de-chroming from oven cleaner and bleach to other things like brake fluid. Not sure how the others fare but I love the fact that BAM removes the chrome paint instantly, it's brill!

  4. #4
    Join Date
    27th Dec 2007
    Location
    Sydney
    Posts
    3,152

    Default

    It was sold as something to clean pots and pans. I found it at a dollar store for well, a dollar, then it disappeared never to be seen again. Lucky I bought around 8 bottles

  5. #5
    Join Date
    31st Jan 2009
    Location
    Perth
    Posts
    1,167

    Default

    i have been using nail polish remover to strip the chrome. it works but you need quite a bit of it (cos it evaporates quickly). it also stinks like hell and can damage furniture like table tops if you spill it...
    might have to give Easy Off Bam or Dawn Power Dissolver a go instead.

    i bought a whole bunch of those Kosutte Gin-san powders and have been messing around with different things trying to get the technique right.

    on white plastic, the chrome has a yellowy tint depending on the viewing angle.
    on black and also blue plastic, it looks really dark.
    on flat plastic, the chrome is pretty dull so you definitely need glossy plastic.

    logically, i would assume that plastic with a glossy grey coat should give the best results so i'll give it a go next time. otherwise, i'll revert to applying more coats on the gloss black plastic and hopefully it will make it lighter.

  6. #6
    Join Date
    14th Nov 2008
    Location
    Perth
    Posts
    2,783

    Default

    How are you applying the primer, via an aerosol can or airbrush? If the latter, what are you thinning the paint with?

    I'll be using Tamiya Gloss Black & Tamiya thinner using an airbrush. I've read that using cheaper thinning alternatives (like Windex) will dull the gloss effect so are probably best avoided when using Kosutte Gin-san, Alclad 2 etc.

    Navy blue is meant to produce good results too, can't wait to experiment (come on posty, where's my airbrush already )!

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •